IFRA Maximum Skin Exposure Levels:

Baby Lotion: 0.16%	Bath Water: 0.94%	Body Lotion: 0.56%
Body Powder: 0.56%	Body Wash: 0.94%	Candle: 100.00%
Conditioner: 0.94%	Deodorant: 0.84%	Dry Shampoo: 0.37%
Eye: 0.37%	Face Cream: 0.47%	Face Mask: 0.37%
Face Wash: 0.94%	Hand Cream: 0.47%	Lip: 0.00%
Perfume: 13.09%	Pet Shampoo: 0.94%	Pet Spray: 5.89%
Reed Diff.: 0.94%	Room Spray: 5.89%	Shampoo: 0.94%
Shave Cream: 0.94%	Soap: 0.94%

Elements Bath & Body. certifies that this fragrance product is in compliance with the standards of the International Fragrance Association, provided the fragrance is used in the above application (s) at the noted maximum concentration level(s). The "Maximum Use Level for Skin Exposure" is the amount of fragrance, flavor and essential oil that can come in contact with the skin. It does not mean that your base product can perform at these levels. You must test each oil in each application for evaluation of desired performance. Baby products have lower use levels than those listed above. If a desired application is not listed above, please call us at 1-800-359-0944 for maximum skin levels for skin exposure.

BATH & BODY PRODUCTS: 1-3% is considered the general "skin safe" ratio for lotions, creams, bath salts, fizzies, scrubs, body butter, salves, shampoo, conditioner, body spray, shower gel, etc.

COLD PROCESS (CP) SOAP: 0.7 - 1 oz per lb. Delicate florals should be batched at cool temps.

If a fragrance doesn't note it's compatible in HP, is it? Typically, if it's CP compatible, then yes, it's HP compatible. Usually, the exception is fragile florals (jasmine, gardenias, etc) and essential oils. Add fragrance oils last, after the cook phase or at trace and right before pouring into mold...this way there is less evaporation from the prolonged heat. However, you must stir this rather thick mixture very thoroughly.(For both Hot process in the oven, in a pot, or in a crockpot).

FIXING A SEIZE! Hot-Process is a great way to fix a CP seize in the pot.
Hot processing on the stove or in a double boiler setup to save a seized batch. You will typically need to add an extra ounce of water per lb of soap to make it easier to stir and to smooth into your mold, but this is an excellent way to fix a batch that has seized. You don't want to "cook" the bottom of your pot, so keep heat very low or use a double boiler to ensure your soap doesn't burn. Add your extra water and heat; it will go into the gel phase fairly quickly and only needs to "cook" a little longer to make pouring into the mold easier. It will not be liquid like CP soap, but it should be made fluid enough to smooth into a mold without lumps and air bubbles. Patience here is the key, as you will need to cure as long as with CP simply to allow the extra water to evaporate fully. You may choose to use less water to get a harder bar faster, BUT this will result in a thicker "glob" of soap that will be difficult to smooth into your mold, so the final texture of your soap may suffer.

MELT & POUR (MP) SOAP: 1 TBS per lb, up to .5 oz per lb or 1-3%

PARAFFIN WAX: 1 oz per lb. (Average usage of fragrance oil is approx. 6 - 7% per lb.)

SOY WAX: 1 oz per lb. unless otherwise noted

Note: The above are general guidelines. Individual testing and formulating is necessary

International Nomenclature of Cosmetic Ingredients (INCI):
Fragrance

Common Name Ingredient Listing (FDA Approved):
Fragrance